Turn key off and on 6 times within 5 seconds ending with key on.
Turn the key off and allow the system to power.
How do you reset the transmission light on a Allison Transmission?
Transmission Service Indicator Light Reset
To reset the service indicator light.
Turn the key on, do not start the engine.
Move the shift selector to N-D-N-D-N-R-N, pausing briefly (less than 3 seconds) between each selector movement.
What does F mean on transmission?
Flashing “F” in Gear Display
Indicates that the transmission has detected an Active fault code.
How do I reset my Freightliner code?
How do you read a Freightliner fault code?
What is an SPN code?
The Suspect Parameter Number (SPN) is diagnostic fault code terminology found on some Caterpillar ® products using a J1939 CAN data link.
How do I reset my Freightliner Cascadia?
How do I get the Flash code for my Freightliner?
What could cause the MIL to flash?
Unburned fuel going to the catalytic converter is what causes the flashing light. This usually comes from misfires. You may want to check for a leaking injector that might be flooding a cylinder when the engine is off. During normal driving, the cylinder may not have a problem burning the injected fuel.
What does EnG 0 mean on a Freightliner?
My 2014 Freightliner M2 106 has EnG 0 code, the yellow check engine light and brake light are on but the truck is drivable fine. This usually means that the engine ECM is not communicating or you have a data link communication problem with the engine ECM and between the other controllers.
How do you check the codes on a 2014 Freightliner Cascadia?
What does Freightliner check engine light mean?
A — Generally a yellow “Check Engine” light tells you that there is a problem that needs checked out. Usually it is not a mission-disabling problem, just something that needs attention. A red “Engine Shut Down” light means that there is a mission-disabling problem that needs attention right away.
What is EEC on Freightliner code?
“EEC 61 is basically saying there is a problem in the After-treatment control module. This is the module the engine uses for the after-treatment system. Your Check Engine Light, and/or your Maintenance light will be on at the same time. The maintenance light is the light that looks like a solid yellow engine.
What does ECU 128 mean on a Freightliner?
On the Mercedes Freightliner Sprinter engine, ECU 128 is not a fault code; it just refers You to the electronic control unit, where Your fault code will lie. It indicates that the ECU engine has a secret in it. ECU 128 just recognizes the module, it’s not a fault address.
What does BH 164 mean?
bh164 means there is a fault with the bulkhead module. If you press the button when the fault comes up, it should give a sid and a fmi.
What is a bulkhead module on a Freightliner?
The Bulkhead Module (BHM) is the primary module of the vehicle electrical system, and controls the operation of the other multiplex modules in the system and a variety of other vehicle components either directly or indirectly.
What is a Freightliner Smart Switch?
• Smart switches are optional low-current switches that are connected. to the Bulkhead Module (BHM) or to an optional Switch Expansion Module (SEM) on a Business Class® M2 vehicle. A smart switch is used to activate an optional feature on the vehicle. •
What does BH 33 mean?
BH 33 is basically just identifying your bulkhead module or in other terms, body controller. If you scroll through using the mode switch to the following screens that is where you will actually see or be able to display the fault codes that are logged within that bulkhead module. BH 33 is not an a fault code.
What is CAB 33 code on a Freightliner?
CAB 33 is a general cabin SAM fault, you need to get a more specific message by pushing the square button next to the display while the truck is stopped.