What cfm carb do I need for a 350?

A 600-cfm carburetor may perform quite well on a stock 350 Chevy. However, the minute you start weaving in power adders like a hotter cam, a dual-plane performance intake manifold, and aluminum heads you’re going to need 700-750 cfm.

What happens if carburetor is too big?

An engine with a carb that is too big will put out less Torque and Horsepower . It will be difficult to drive due to poor low-end torque. If you drag race your car, an oversized carb will produce slow 60 ft. times.

How much horsepower will a 650 cfm carb support?

450-470 hp
So, using your Google-Fu you type “How much power can a 650 cfm carb support?” Well, chances are that you’ll get answers in the 450-470 hp range, but that’s not really the right way to look at it. In fact, horsepower—or even torque, for that matter—doesn’t matter at all.

What size carburetor do I need for a 355?

To arrive at the most appropriate carburetor choice, there’s a basic formula: engine displacement multiplied by maximum rpm divided by 3,456. For example: a typical 355ci small-block—a 0.030-over rebuild—with a 6,000-rpm max engine speed would work well with a 616-cfm carb ((355 x 6,000) 3,456 = 616.32).

What size carb do I need for a 383 stroker?

Carburetor For 383 Stroker

recommends a 650 cfm carburetor. A 750 cfm carburetor will make the engine more powerful, but it is the largest that should be used unless the engine is being used for racing.

What is a better carburetor Holley or Edelbrock?

As I mentioned before, right out of the box an Edelbrock will be better. However, if you’re a DIY guy who likes modding things around – Holley will be your best pal. The tuning is more responsive and less touchy than not only Edelbrock, but most other manufacturer’s carbs.

Why use a double pumper carb?

The reason double pumpers (mechanical secondary carburetors is their proper name) have these twin accelerator pumps is to prevent a momentary lean situation during quick throttle blade movement. All carburetors use an accelerator pump circuit, however many only have one on the primary barrels.

Are carb spacers worth it?

Spacers are said to improve air/fuel vaporization through and out of the carburetor. Anytime the air/fuel charge has to turn sharply coming off the carb, it increases the chance of separating the fuel from the air.

Who makes the most reliable carburetor?

Out of 13 brands of carburetors, enthusiasts elected Advanced Engine Design (AED), Edelbrock, and Holley (in alphabetical order) as the top 3 most reliable brands of carburetors.

What are the 3 types of carburetors?

There are three general types of carburetors depending on the direction of flow of air.
  • Types of Carburetors.
  • Constant Choke Carburetor:
  • Constant Vacuum Carburetor:
  • Multiple Venturi Carburetor:

Are Edelbrock 750 carbs good?

The Edelbrock 750 Performer has a reputation as a carburetor that works very well right out of the box. … To tune this carb, you will need to purchase a kit, but the price is reasonable.

How good is a Holley carburetor?

It seems Holley has paid attention and are doing some serious quality control. These carbs are now as reliable as they are powerful. If you have a stock to semi hot small block or hot small cube engine, this is the carb for you. Would also run well on a stock larger cube engine in a big car with highway friendly gears.

Are quick fuel carbs made by Holley?

Registered. Just for your info, Quick Fuel carbs are made at the Quick Fuel facility and Holley carbs at the Holley facility.

What is the difference between a Holley 4150 and 4160 carburetor?

These two are very similar with the primary difference that the 4150 uses a thick metering block in both the primary and secondary while the 4160 is shorter in length and uses a thin, metering plate on the secondary side.

How do I identify a Holley carburetor?

It’s like a “VIN” for your carburetor and should be hand-stamped on the front of the choke tower to the right of the vent tube on most typical Holley carbs. The list number typically is four to six digits long and may or may not have a suffix number behind it.

Where are Holley carburetors made?

Bowling Green, Kentucky
If you’ve driven a car equipped with a Holley carb, chances are that carburetor was built in Holley’s Bowling Green, Kentucky, factory. That’s because Holley has been building carburetors in the same facility for more than 50 years.

How do Holley carburetors work?

Holley carburetors use a parallel air well that transfers air into the main well through two, three, and sometimes five holes that can be seen in the metering block photo (page 36). While this passage is called an air chamber, fuel still resides in this chamber at the same level as the fuel in the float bowl.

How do I know what carburetor I have?

Look at the upper front of the carburetor on the piece known as the airhorn, or choke tower. This is a rectangular part of the carburetor with rounded edges, open to the top of the part. There will be a small number stamped there.

What is a Holley 3310?

Once described as the small block Chevy of fuel delivery, the Holley 3310 carburetor (4150 and 4160 models) is still the go-to carburetor for anyone building a performance engine. … The legendary Holley 3310 was born. The 3310 feeds the Z16 Chevelle’s 396 big block with 780 cfm of air.

What size is a Holley 4150?

16″
Features:
Base Style 4150
Material Stamped Steel
Product Type Air Cleaner
Size 16″
Warranty Limited 90 Day

How do I know what size Edelbrock carburetor I have?

Where is the carburetor number on a Briggs and Stratton?

What is a 4150 style carburetor?

The 4150 carburetor was first introduced for the 1957-58 Ford Thunderbird. … Often referred to simply as the “double pumper,” the 4150 and 4150-style carburetors fuel-feed inlets and a second full metering block on the secondary side, giving it dual accelerator pumps.

What do the numbers on Edelbrock carburetor mean?

What size is a 1405 Edelbrock carb?

Edelbrock’s 1405-model carburetor has a primary main jet that measures 0.100 inches, and a secondary main jet that measures 0.095 inches. The primary metering rod measures 0.070 by 0.047 inches, and the needle and seat measure 0.0935 inches.