How do I reset my Pentair Intellichlor salt cell?

Press the “More” button to cycle through each salt level, and then press the “Less” button to choose and save the display as the new salt level. The “PWR”, “Cell”, “Life”, and “Flow” lights will flash 4 times, then the mode exits to normal.

How do you calibrate a salt chlorinator?

Turn Salt System Off and On

With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.

What percentage should my salt chlorinator be set at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

Why is my salt cell flashing?

If the “Inspect Cell” light flashes by itself it is an early indication that the salt generator needs a manual reset. Each cell is equipped with 500 operational hours and requires a manual reset once it expires. To reset the cell, hold down the “Diagnostic” button for 3-5 seconds.

How do you reset a salt chlorinator?

To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.

How do you reset the check cell on a saltwater pool?

Reset AquaRite Salt Chlorination Inspect Cell Light

If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.

How do you test an Intellichlor salt cell?

Submerge the salt cell in a bucket of pool water, but do not get the wiring connections wet. Turn on the pump and activate the salt system. Put the output on the salt system at 100% for this test. Put the output back to the original setting when you are done.

How do I know if my Pentair salt Cell is working?

How do I know if my salt water generator is working?

The first step is to confirm that power is reaching the salt chlorinator control box. Make sure that the system is plugged into a GFI outlet, and the test button is not popped or tripped. The control panel has lights that indicate that the power is reaching the system.

How do you test a salt cell?

Why is my Pentair salt cell not producing chlorine?

High phosphates in the water, a chemical can be purchased at your local pool store or through us to remove higher than normal levels of phosphates. … If the water is too cold below 70-65 degrees your chlorinator will not be able to produce chlorine even if your salt level is perfect.

What causes a salt cell to fail?

Salt cells fail for a few different reasons, the main reason being lack of proper maintenance. It is very important to check the cell regularly for excessive buildup. … Use a cleaning kit designed for salt cells to keep the plates clear of buildup. Another common cause of salt cell failure is improper water balance.

How long after adding salt to pool can you test?

After 24 hours you should then test the salinity and if you still need to add swimming pool salt you can repeat the process again making sure to not turn on the chlorine generator until you are completely satisfied your salinity is within the manufacturers recommended range.

Why are my chlorine tablets not dissolving?

If the tablets are not dissolving, and you get a strong smell of chlorine when you open the chlorinator, you probably have a bad check valve in the chlorinator. It is not allowing any water to move through the chlorinator, and any water that is there simply sits there and builds up a yellowish chlorine gas.

How do I know if my Pentair chlorinator is working?

The easiest way to ascertain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights. Ensure there is enough salt in the pool. On the chlorinator box there should be a light or dial that indicates it is working.

How do I add salt to my pool for the first time?

Can I get in pool after adding salt?

It’s recommended to wait at least 20 minutes to swim after adding salt to your pool. If you’re adding calcium chloride to your pool water, it’s recommended to wait two to four hours before swimming again.

How many bags of salt do I need to start my pool?

Setting Up a Salt Water Pool

How much salt to add to the pool? To reach the initial salt level recommended by the salt system manufacturer (usually 2400-3200 ppm), you will need to add about 200 lbs of pure pool grade salt (NaCl), per 10,000 gallons of water.

Can I add salt and chlorine at the same time?

If your pool is truly low in salt, then you can add salt at any time, but you need to use external sources of chlorine such as chlorinating liquid to shock your pool to eliminate the algae; you can’t eliminate the algae in a bloom fast enough with an SWG alone..

Why do I have to keep adding salt to my pool?

Salt is usually needed due to loss because of backwashing the filter, bathing suit drag out, water splash out, leaks, or rainwater overflow.

Does a saltwater pool need to be shocked?

Salt pools are, in fact, sanitized using chlorine. A salt-chlorine generator separates the chlorine and sodium molecules in salt and reintroduces them into the pool water. … All pools, no matter what the sanitizer, need to be shocked regularly– preferably once per week during warm weather.

How often do you add salt to a saltwater pool?

There is no set timeframe of when you need to add salt to your pool. Because salt does not dissipate from your water, the only time you would add salt to your pool is when you add fresh water or after heavy rain that dilutes salinity levels.

How long should I run my salt chlorinator?

Run your system to run for 8-12 hours a day and set the chlorine output on the generator to 50%. After testing and determining the free chlorine readings over a few days, adjust the output on the generator only.

Does shock raise salt level in pool?

In addition, most salt systems placed in “Shock Mode” will only raise the FC level by a few clicks – up to 5-7 ppm. It also does it very slowly, which will not have the desired effect of killing algae, removing chloramines or pathogens.